Monday, June 1, 2015

DIY: Rabbit Hutch


Raising rabbits is something I have been wanting to do for some time now.  I have always managed to push it to the back burner because my wife is not as keen to the idea as I am.


When my neighbor approached me about building some rabbit hutches for his daughter, I immediately jumped at the chance.  I figure this is as good an opportunity as ever to get this project off the ground for our own homestead.

What good are rabbits on a homestead you may ask?  Well...

1.  You can raise them for food for people.

2.  You can raise them for food for your pets.

3.  Bait.

4.  There droppings can be used to feed a worm bin.

5.  There droppings can be used directly in your garden beds.

6.  In the United States, rabbits are not pumped full of medication and antibiotics like other commercially raised livestock animals.

7.  They are easier on the environment to raise and require less feed to do so.

So as you can see their are a myriad of reasons to raise rabbits on a homestead both big and small.

DIY: Rabbit Hutch


VIDEO

 

Cut List


The below measurements and cut list are for one single hutch unit.  There are three units depicted in the photo above. 

If you want 2 hutches then multiply the number of each cut by 2.

If you want three of them then you can multiply by three if you want to keep it simple.  I did away with the side slates for the middle unit.  While this lowered the amount of lumber needed for the project it also adds a bit of complexity to the project.

Eliminating those side slates for the middle unit changes some of the other measurements for that unit.  It would be too complex and somewhat confusing to list two different sets of measurements for this blog post.

Also, I had to ask myself how many people would actually want or have space for a three set unit like this.  I assume most will only want one, so that is what I posted for the cut list.


Frame




2 vertical front frame pieces @ 1.5" x 1.5" x 24"

2 horizontal bottom frame pieces @ 1.5" x 1.5" x 18-15/16"

2 vertical back frame pieces @ 1.5" x 1.5" x 18-15/16"

1 Horizontal bottom back piece @ 1.5" x 1.5" x 25.5"

1 Horizontal bottom front piece @ 1.5" x 3.5" x 25.5"

1 Horizontal top front frame piece @ 1.5" x 3.5" x 25.5"

2 Top Frame pieces @ 1.5" x 1.5" x 19-5/8" (with a 15 degree angle cut on both ends.  Be careful to make each cut in the right direction.)

14 - 1x4's Side Slats @ 21-15/16"

 5 - 1x4's Back Slats @ 30"

Face Frame


2 Rails @ 2.75" x 30"
2 Stiles @ 2.25" x 18.5"

Door 

 

The door is a simple rail and stile type of construction.  As I state in the video, whatever works for you, works in this situation.  It is a rabbit hutch and not fine cabinetry.  

I used a combination of joinery methods.  I started off with dowels using my DIY dowel jig.  I did not realize how low I was on dowels so when I ran out I switched to biscuits using my biscuit joiner.  Not wanting to wait on glue to dry I then switched to simple pocket hole joinery to finish the doors up.

Point taken?  Excellent!  Right or wrong is a perception that rests in your hands.  If it works it works.  It may not be right for everyone but it is right for someone. 

2 Stiles @ 2.5" x 12.5"
2 Rails @ 2.5" x 24-7/8"

Roof

 

The corrugated sheet metal roof size is listed for one unit only.  You can purchase an 8 foot strip of sheet metal at any home improvement store.  If you get one that is 36 inches wide then you can measure 33 inches and get three equal sized cuts out of it.  One 36" by 33" piece will cover one rabbit hutch unit.  If you build three of them as I have done then you should have zero waste.

1 piece of Corrugated Sheet Metal @ 36" x 33"

Base Stand

 

The base unit stands at around 20 - 3/4" tall.  The legs get cut at 20" and then attached 3/4" down from the top of the frame.  A simple spacer block of a piece of scrap from the side slats works well.

Assemble the top rectangular frame first on a flat surface.  (I used my garage floor.)  Then place the spacer block down and attach the legs to the inside of the frame.

The 1.5" by 1.5" rail pieces are attached next using the same spacer block.

The corner braces I cut at 12".  Then I cut the 45 degree angles on both sides.  Place them in each corner and attach with 3" screws.

Obviously measure appropriately if you are only building one or two hutch units.

What I usually do is build the unit first.  Then measure width and depth.  Add an inch and a half to both measurements.  That should be the dimensions of the base unit.

2 - 2x4's @ 91.5"
2 - 2x4's @27. 5"
2 - 2x2's @ 18.5"
2 - 2x2's @ 88.5"
4 - 2x4's @ 20"
8 - 2x4's @ 12"

 

Additional Materials:

 

4' of Hardware cloth (one unit only.  If you want 3 units, you will need 12' of hardware cloth)
2 - Hinges
1 - Latch
1 - Handle (Optional)



Other supplies

1-3 rabbit water bottles
1-3 rabbit food dispenser feeders

You can certainly build your own feeder like we did. See how we did it here:

Final Thoughts


This is a very versatile design that will fit in a wide array of spots and spaces.  They are sturdy and strong.  I enjoyed building them for my neighbor and have even completed my own second design.

Yep, you read that right and here it is!




Check back often and don't forget to check me out on Facebook, Pinterest and if you haven't yet, find me on YouTube. Welcome to our channel!

Happy DIY'ing!!



9 comments:

  1. Replies
    1. I do not presume to tell people what they should or should not do with their rabbits. I just share how to build projects.

      Delete
    2. so what wood do you get to build it. All the wood in all...total..

      Delete
    3. I'm going to raise meat rabbits.
      Then I'm going to move on to Meat Chickens.
      Then Meat Goats.
      Then Meat Pigs.
      Then Cattle.
      That's the progression.
      If they legalize it, I'll move on to Meat Vegans.

      Delete
    4. Rabbits are amazing to eat! Yum!

      Delete
  2. so what is the material list for this project

    ReplyDelete
  3. Great plan. Nice job. I just finished this project last night and it turned out great.

    ReplyDelete
  4. What is the shopping list for the entire project

    ReplyDelete
  5. By chance do you have a PDF plan of this hutch? As an old man these days it's easier for me to look at a diagram plan drawn up. We have to make new hutches for 11 new kits. Thanks.

    ReplyDelete

Comments are held for moderation before they are published. If you would like to be notified of responses please check the "notify me" box.

http://www.simplyeasydiy.com/search/label/Beginners